User Guide
v2025.03
v2025.03
  • Extend Robotics User Guide
  • introduction
    • Release Notes
      • AMAS v2025.03
      • AMAS V10.3
      • AMAS V9.3
      • AMAS V8.3
      • AMAS V7.6
    • AMAS Overview
    • Compatible XR Systems
    • Supported Robots
      • Robots
        • Ufactory
        • Universal Robots
        • Dobot
        • Pal Robotics
        • Mitsubishi Electric
        • AGILE-X
      • Accessories
        • Robotiq
        • ROBOTIS
        • Ufactory
        • On Robot
    • Choosing 3D Sensors
      • Limitations
      • Sensor Types
      • Support Matrix
      • Visual Comparison
    • Specifications
    • PC Requirements
    • Typical Network Connection
    • Network Requirements
  • getting started
    • Getting Started with AMAS
    • Navigating Through the User Guide
  • Cortex
    • Introduction
    • Robot Setup Instructions
      • UFactory xArm
      • UR e Series
      • UR CB Series
      • Dobot CR-A Series
      • AgileX
      • Dexterous Hands
        • Robotera XHAND1
        • Inspire Robots Dexterous Hand
      • Extend Avatar
        • Electronics Assembly
        • Mechanical assembly
          • Avatar Component Parts list
          • Assembly Instructions
        • xArm Adjustments
    • Sensor Setup Instructions
      • Sensor Positioning
    • Cortex Firmware Configuration
    • Instructions for Starting the Cortex
    • Cortex IP Configuration
    • Shutdown Instructions
    • Cortex Safety Protocols
  • AMAS VR Application
    • Download AMAS
      • Setup Quest Application
      • Running the Application
      • Home Scene Arrival
    • Control Panel
      • Interactions Modes
        • View Adjust Mode
        • Robot Control Mode
        • Interaction Utilities
      • Floating Keyboard
      • Error popup
      • Web Browser
    • Hand Tracking
    • Hand Gestures
    • Upper Body Tracking
    • Passthrough Mode
    • Managing Cortex
      • Adding Cortex Connection
      • Loading Cortex Connection
      • Modifying Robot Settings
        • Safety Parameter Update
      • Manual Robot Positioning
      • Modifying Sensor Settings
        • 2D - 3D fusion
      • Sensor Position Calibration
        • Calibration Prerequisite
          • Calibration Board
        • Sensor to Robot Calibration
        • Sensor to Sensor Calibration
        • Manual Calibration
    • Accessories
      • SenseGlove Nova 2
      • bHaptics TactGloves
    • Record and Replay
      • Creating a Recording
      • Load a Recorded Motion
      • Replay a Recorded Motion
    • Data Collection
      • Recording Data
      • Data Visualisation
        • ROS Bag
        • HDF5
        • LeRobot
    • Tutorial
    • Visual Haptic
      • Force Torque Calibration
    • Speech Recognition
    • Utilities
      • Stationary Headset
      • Exhibition Scene
    • UR Program Change
    • Mobile Robot Movement
      • Virtual Joystick
      • Quest series controller
    • Shutdown Instructions
    • Safety Utilities
      • Safety Utilities
      • Joint Limit Recovery Visualisation
      • Robot Rescue
    • Avatar Additional VR Functionalities
      • Avatar Digital Twin Assembly
      • Pose Sync Avatar Camera Setup
      • Torso Initialisation
      • Embody Control Mode
  • Command Console
    • Over-the-Air Firmware Updates
    • Updating Robot/Sensor Configurations
      • Robot Specific Firmware Settings
      • Sensor Specific Firmware Settings
  • Cortex API
    • Robots
      • Current Robot Publishers, Subscribers and Services
      • Gripper Customizations
      • Message and Service Definitions
    • Sensors
  • Other Information
    • Troubleshooting
    • Customized Hardware Integrations
    • Remote Demonstration Requirements
    • Guides
      • PAL TIAGo
        • Mobile Base, Arm and Torso Control
        • 3D Sensor
        • Additional Sensor Data Visualization
        • First Person View Mode
        • Take Home Functionality
        • Audio
        • Bundle
      • Robot - Sensor Sync
Powered by GitBook
On this page

Was this helpful?

  1. Command Console

Over-the-Air Firmware Updates

Guide to Upgrade your Firmware of RoboKit and SenseKit through the ER Command Console

PreviousEmbody Control ModeNextUpdating Robot/Sensor Configurations

Was this helpful?

With the introduction of singular cortex devices, we have released the Extend Robotics , a web interface connected to your cortex device as well as the Robots and Sensors. It has a built-in functionality for updating the firmware for the designated RoboKit(s) and SenseKit(s).

For hardware delivered with version 9.3 or earlier, you must contact so we can set up your Command Console account, allowing for seamless future updates.

Stay up-to-date with the latest improvements and enhancements by keeping your Cortex, RoboKits and SenseKits firmware updated. This section guides you through the process of performing over-the-air firmware updates for seamless device maintenance.


1. Login to the Command Console and you should be redirected to the Dashboard.

2. Click on Manage your device for the particular device you would like to update. Note that the device must be online and connected to the internet for any changes to take place.

3. Navigate to the Update your Device Firmware dropdown:

4. Select the latest firmware version available (or whichever version you wish to update to)

5. Select the settings you would like to turn on and off for the firmware update. The device must be rebooted after the firmware update, and we recommend deleting old firmware installations.

6. When you are ready, click on the Update Firmware button

7. Upon a successful action creation, a little popup will appear. Click on View updates.

8. Check the status of your Update Firmware Action. The page refreshes every 15 seconds, or you can click on Refresh

9. Wait until you observe the Succeeded status and click on Succeeded for more details

Command Console
support@extendrobotics.com
here