User Guide
v8.3
v8.3
  • Extend Robotics User Manual
  • introduction
    • AMAS Overview
    • Compatible XR Systems
    • Supported Robots
      • Robots
        • Ufactory
        • Universal Robots
        • Dobot
        • Pal Robotics
        • Mitsubishi Electric
        • AGILE-X
      • Accessories
        • Robotiq
        • ROBOTIS
        • Ufactory
    • Choosing 3D Sensors
      • Limitations
      • Sensor Types
      • Visual Comparison
    • Typical Network Connection
    • Specifications
    • Release Notes
      • AMAS V7.6
      • AMAS V8.3
  • getting started
    • Getting Started with AMAS
    • Navigating Through the User Guide
  • AMAS VR Application
    • Download AMAS
      • Setup Quest Application
      • Running the Application
      • Home Scene Arrival
    • Control Panel
      • Floating Keyboard
      • Error popup
    • Interactions Modes
      • View Adjust Mode
      • Robot Control Mode
      • Interaction Utilities
    • Hand Tracking
    • Passthrough Mode
    • Manage multiple devices
      • RoboKit Addition and Configuration
      • Loading RoboKit
      • SenseKit Addition and Configuration
        • Sensor Specific Firmware Settings
        • 2D - 3D fusion
      • Loading SenseKit
      • AudioKit Addition and Configuration
      • Loading AudioKit
      • Configuration Bundles
    • Hand-eye Calibrations
      • Calibration Prerequisite
      • SenseKit to Robot Calibration
      • SenseKit to SenseKit Calibration
      • Manual Sensekit Calibration
      • Manual RoboKit Calibration
    • Motion Playback
      • Creating a Recording
      • Load a Recorded Motion
      • Replay a Recorded Motion
    • Visual Haptic
      • Force Torque Calibration
    • Speech Recognition
    • Utilities
      • Stationary Headset
    • UR Program Change
    • Mobile Robot Movement
      • Virtual Joystick
      • Quest series controller
    • Shutdown Instructions
    • Over-the-Air Firmware Updates
    • Safety Utilities
      • RoboKit Safety Utilities
      • Joint Limit Recovery Visualisation
      • Robot Rescue
  • SenseKit
    • Introduction
    • Components
      • Pre-requisite SenseKit Components
      • Shipped SenseKit Components
    • Mounting Options
    • Setup Instructions
    • Running Instructions
    • SenseKit IP Configuration
    • Calibration Instructions
    • SenseKit Manual Firmware Upgrade / Install
    • Shutdown Instructions
  • RoboKit
    • Introduction
    • Components
      • Pre-requisite RoboKit Components
      • Shipped RoboKit Components
    • Initial Setup Instructions
      • UFactory xArm
      • UR e Series
      • UR CB Series
      • Dobot CR-A Series
      • AgileX
      • Dexterous Hand with xArm
    • Instructions for Starting RoboKit
    • RoboKit IP Configuration
    • RoboKit Manual Firmware Upgrade / Install
    • Shutdown Instructions
    • Safety Protocols
  • API
    • RoboKit
      • Current Robokit Publishers, Subscribers and Services
      • Gripper Customizations
      • Message and Service Definitions
    • SenseKit
  • Other Information
    • Troubleshooting
    • Customized Hardware Integrations
    • Remote Demonstration Requirements
    • Backward Compatibility
    • Guides
      • PAL TIAGo
        • Mobile Base, Arm and Torso Control
        • 3D Sensor
        • Additional Sensor Data Visualization
        • First Person View Mode
        • Take Home Functionality
        • Audio
        • Bundle
      • Robot - Sensor Sync
      • UI Design Reference
    • Downloads
      • OTA
      • Calibration Board
  • System Requirements
    • PC Requirements
    • Network Requirements
Powered by GitBook
On this page

Was this helpful?

  1. SenseKit

Shutdown Instructions

Guide to safely shut down your SenseKit.

When you're finished using the SenseKit, follow these instructions to shut it down correctly:

  1. Exit the AMAS application by pressing the esc button on the laptop keyboard.

  2. Power Off the SenseKit by pressing and holding the power button until the indicator lights turn red.

PreviousSenseKit Manual Firmware Upgrade / InstallNextIntroduction

Last updated 9 months ago

Was this helpful?